Malaysia Hot Selling Efficient Hammer Mill Wood Chips Hammer Mill Grinder

Malaysia Hot Selling Efficient Hammer Mill Wood Chips Hammer Mill Grinder         Brief Introduction of Efficienct Hammer Mill:   Efficienct Hammer Mill Machine working principle is that when the materials enters into crusher room , materials are grinded by the beat , friction power from the higher speed rotating hammers , then the required powder screened by the sieve . It is suitable for corn straw, wheat straw, cotton stalk, straw, rice husk, peanut shell, corn cob, wood branches, leaves, sawdust ,wood factory waste  ,PVC foam board and other raw materials .   Detailed Parameters of BLFS65*55 Efficient Hammer Mill:  

Machine model	BLFS65*75
Power	37/45kw
Capacity	1-2 t/h
Hammer qty.	72 pcs
Sieve qty.	2 pcs
Sieve diameter	10mm
Grinding chamber width	55cm
Feeding belt conveyor	8m, with pit
Fan blower	11kw
Cyclone	1000mm diameter
Air lock	12L
Bag dust collector	16*250mm
Air pipe	200&250mm
Highest point to floor	6m
Main shaft rpm	2980rpm
Hammer material	Manganese steel, Tungsten carbide spot welding on hammer  head, harder, lime-time longer

    Advantages of Efficienct Hammer Mill:   1. One set complete hammer mill contain fan blower , cyclone , air lock , bag dust collector , electrical control cabinet . 2. Motor we use 2- class efficient motor. 3. Hammers grinding the material into powder , then the fan blower absorb powder to cyclone , in the end the airlock discharge the powder to next section . 4. Special design two pieces screeners make the machine have high efficiency and capacity . 5. Fully opened operating door, convenient maintenance and easy to replace hammer . 6. The high efficiency hammer mill can crush the wood chips , agricultural waste like the corn cob , penut shell , grain crops . 7. It is widely used in wood pellet production line , animal feed production line . 8. Reasonable design, scientific use of the hammer mill operating principle, the side to improve the speed of hammer mill to combat materials. 9.The design changes the material’s movement line in the crushing room , make full use of crushing room space to expand the crushing area, and the maximum protection of the sieve, extend the service lifetime of the sieve more than 1 times. 10.Noise of the hammer mill: tested, no-load noise of 102 decibels, load noise of 95 decibels, and 65X55 single rotor hammer mill is basically the same. 11. The machine is running smoothly, running, the stability is better than the single rotor hammer mill.     Parameters of Efficienct Hammer Mill:  

Model	Power(kw)	Capacity(t/h)	Hammer qty.	Screener diameter	discharging and dusting system
YSG50	15	0.3-0.5	16	8/10mm	Fan blower, cyclone, air lock, bag dust collector system
BLFS65*27	22	0.5-1	24
BLFS65*55	37/45	1-2	72
BLFS65*75	55/75	2-3	108
BLFS65*100	90/110	3-4	144

    Efficienct Hammer Mill Product Design Advantages And Practical Function Advantages:  

	Easy to change the hammer
Wear-resistant slab: mainly to install the two sides of the pulverizer.   1. In order to better smash the material to achieve the smashing effect   2, Protect the smashing the chassis body, prevent the damage of the material to the smashing chassis   3.Using cast iron once molding, with the tradition Compared with welded threaded plates, it is not easy to fall off, and the effect is good.
	Hammert mill screen card slot for fixing the bottom screen for easy installation and removal
The rotor main shaft is made of 40Cr material, and the rotor disc is made of 45# cast steel. The main shaft has large diameter, large bearing capacity, no deformation, no influence on balance, long service life and high stability.   The rotor is tested by dynamic balance tester and runs stably.
	The coupling between the motor and the rotor shaft is directly connected, the kinetic energy loss is small, efficiency high.
Advantages of discharging port design:   1. There is a cleaning port to clean up the impurities in the sawdust material and other impurities.   2. than the traditional arc interface, it is convenient to install the duct, simple and convenient
	1. Increase the legs at the bottom and raise the fuselage. In order to give the material a simple over-slurry after the material is crushed, the material will not accumulate in the crushing chamber, and the long time will affect the output.   2. The bottom adopts a semi-arc type device, no dead angle, the material will not accumulate, and the circulation is good.
Bottom damper: It can be adjusted according to the moisture and specific gravity of the material, so that the material circulation can flow smoothly from the pulverizer in the first time, and the productivity can be improved.
	The crusher adopts a negative pressure connection method to ensure that the impeller of the fan is not worn and blocked.

  Company Show:     More Products Show:       Shandong BOLIDA Machinery CO.,LTD. specilized in crushing series machine, biomass pellet production line machines. If any needed, feel free to contact us.     Cynthia Ming  Tel/whatsapp/wechat: +19553130131 Email: machine19@rotexmaster.com  

Contact us if you need more details on Pellet Plant Hammer Mill. We are ready to answer your questions on packaging, logistics, certification or any other aspects about Peanut Shell Hammer Mill、Hammer Mill Grinder. If these products fail to match your need, please contact us and we would like to provide relevant information.

Product Categories : Grinding machine